标准号 |
中文名称 |
英文名称 |
prEN 50313-2-1999 |
光电系统太阳能存储体第2部分:性能测试要求及程序 |
Photovoltaic systems - Solar modules - Part 2: Performance - Test requirements and procedures |
prEN 50314-1-1999 |
光电系统电荷调节器第1部分:安全性测试要求及程序 |
Photovoltaic systems - Charge regulators - Part 1: Safety - Test requirements and procedures |
prEN 50314-2-1999 |
光电系统电荷调节器第2部分:EMC-测试要求及程序 |
Photovoltaic systems - Charge regulators - Part 2: EMC - Test requirements and procedures |
prEN 50314-3-1999 |
光电系统电荷调节器第3部分:性能测试要求及程序 |
Photovoltaic systems - Charge regulators - Part 3: Performance - Test requirements and procedures |
prEN 50315-1-1999 |
光电系统中使用的蓄能器第1部分:安全性测试要求及程序 |
Accumulators for use in photovoltaic systems - Part 1: Safety - Test requirements and procedures |
prEN 50315-2-1999 |
光电系统中使用的蓄能器第2部分:性能测试要求及程序 |
Accumulators for use in photovoltaic systems - Part 2: Performance - Test requirements and procedures |
prEN 50316-1-1999 |
光电照明系统第1部分:安全性测试要求及程序 |
Photovoltaic lighting systems - Part 1: Safety - Test requirements and procedures |
prEN 50316-2-1999 |
光电照明系统第2部分:EMC-测试要求及程序 |
Photovoltaic lighting systems - Part 2: EMC - Test requirements and procedures |
prEN 50316-3-1999 |
光电照明系统第3部分:性能测试要求及程序 |
Photovoltaic lighting systems - Part 3: Performance - Test requirements and procedures |
prEN 50322-1-1999 |
光电系统第1部分:电磁兼容性(EMC)光电抽运系统的要求 |
Photovoltaic systems - Part 1: Electromagnetic compatibility (EMC) - Requirements for photovoltaic pumping systems |
prEN 50323-1999 |
助听器一般要求 |
General requirements for hearing aids |
prEN 50330-1-1999 |
光电半导体转换器第1部分:PV线换向转换器的实用交互式故障自动保护接口设计质量与型式批准 |
Photovoltaic semiconductor converters - Part 1: Utility interactive fail safe protective interface for PV-line commutated converters - Design qualification and type approval |
prEN 50331-1-1999 |
建筑物内的光电系统第1部分:安全要求 |
Photovoltaic systems in buildings - Part 1: Safety requirements |
prEN 50335-2-94-1994 |
家用及类似电器的安全性第2部分:剪式切草机的特殊要求 |
Safety of household and similar electrical appliances - Part 2: Particular requirements for scissor type grass shears |
prEN 50339-2000 |
医疗设备X射线胶片 |
Medical devices - X-ray film |
prEN 50345-2002 |
铁路设备固定设施电子牵引支持高架连接线的绝缘合成绳 |
Railway applications - Fixed installations; Electric traction - Insulating synthetic rope assemblies for support of overhead contact lines |
prEN 50349-2002 |
电气设施承包人的资格 |
Qualification of electrical installation contractors |
prEN 50350-2003 |
贮热式家用室内电加热用充电控制系统测量性能方法 |
Charging control systems for household electric room heating of the storage type - Methods for measuring performance |
prEN 50351-2003 |
有关供电系统与牵引系统对通信系统的影响的计算和测量方法用的主要标准 |
Basic standard for the calculation and measurement methods relating to the influence of electric power supply and traction systems on telecommunication systems |
prEN 50352-2003 |
有关供电系统与牵引系统对通信系统的影响的极限 |
Limits relating to the influence of electric power supply and traction systems on telecommunication systems |
prEN 50359-1-1-2000 |
高级陶瓷第1-1部分:电特性短期的耐电强度的测试方法 |
Advanced technical ceramics - Part 1-1: Electrical properties; Method of test for short term electric strength |
prEN 50359-1-2-2000 |
高级陶瓷第1-2部分:电特性在温度为20℃- 800℃范围内测定表面电阻系数和体电阻系数 |
Advanced technical ceramics - Part 1-2: Electrical properties; Determination of the surface and volume resistivity in the temperature range 20℃ to 800℃ |
prEN 50367-2002 |
铁路设备集电系统架式受电弓和架空线路之间的交互作用用技术标准(可自由伸缩) |
Railway applications - Current collection systems - Technical criteria for the interaction between pantograph and overhead line (to achieve free access) |
prEN 50369-2003 |
电缆的液封外壳系统 |
Liquid tight sheathing systems for cable management |
prEN 50370-1-2002 |
电磁兼容性机床的产品系列标准第1部分:电磁辐射 |
Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission |
prEN 50374-2003 |
导线架设吊篮 |
Conductor cars |
prEN 50379-1-2003 |
用于测量加热器具燃烧烟气参数的便携式电气装置的规范第1部分:一般要求和试验方法 |
Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances - Part 1: General requirements and test methods |
prEN 50379-2-2003 |
用于测量加热器具燃烧烟气参数的便携式电气装置的规范第2部分:法定检查和评估用设备的性能要求 |
Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances - Part 2: Performance requirements for apparatus used in statutory inspections and assessment |
prEN 50379-3-2003 |
用于测量加热器具燃烧烟气参数的便携式电气装置的规范第3部分:非法定燃气加热器具操作用设备的性能要求 |
Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances - Part 3: Performance requirements for apparatus used in non-statutory servicing of gas fired heating appliances |
prEN 50381-2003 |
有或无内部能源的可运输的通风房间 |
Transportable ventilated rooms with or without an internal source of release |
prEN 51-1974 |
道路车辆 牵引车和半拖挂车之间的机械连接器 互换性 |
Road vehicles; mechanical coupling between tractors and semi-trailers; interchangeability |
prEN 520-2000 |
石膏板 规范、要求和试验方法 |
Gypsum plasterboards - Definitions, requirements and test methods |
prEN 54-13-2001 |
火灾探测和火灾警报系统 第13部分:系统要求和兼容性评定 |
Fire detection and fire alarm systems - Part 13: System requirements and compatibility assessment |
prEN 54-14-2001 |
火灾探测和火灾警报系统 第14部分:计划、设计、安装、试运转、使用和维护指南 |
Fire detection and fire alarm systems - Part 14: Guidelines for planning, design, installation, commissioning, use and maintenance |
prEN 55011-2003 |
工业、科学、医疗(ISM)射频设备电磁骚扰特性测量方法和限值 |
CISPR 11, Ed. 4.0: Industrial, scientific and medical (ISM) radio-frequency equipment - Electromagnetic disturbance characteristics - Limits and methods of measurement |
prEN 55021-1999 |
CISPR 21:脉冲噪声对移动无线电通信的骚扰评定其性能暂降的方法和提高性能的措施 |
CISPR 21: Interference to mobile radiocommunications in the presence of impulsive noise - Methods of judging degradation and measures to improve performance |
prEN 55024-2-1994 |
信息技术设备的抗扰性第2部分:静电排放要求 |
Immunity of Information Technology Equipment (ITE) - Part 2: Electrostatic discharge requirements |
prEN 55024-3-1994 |
信息技术设备的抗扰性第3部分:辐射射频场的要求 |
CISPR 60024: immunity of information technology equipment (ITE); part 3: radiated radio frequency fields requirements |
prEN 55024-4-1993 |
信息技术设备的抗扰性 第4部分:抗电子瞬变和瞬爆特性 |
Immunity of information technology equipment (ITE); part 4: immunity to electrical fast transients/bursts |
prEN 55101-2-1991 |
信息技术设备的电磁兼容性要求第2部分:静电放电要求(CISPR/G(CO)10:1991) |
Electromagnetic compatibility requirements for information technology equipment; part 2: electrostatic discharge requirements (CISPR/G(CO)10:1991) |
prEN 55105-1995 |
电信终端设备电磁兼容抗扰性要求 |
Electromagnetic compatibility immunity requirements for telecommunication terminal equipment |
prEN 55106-1995 |
不包括电信终端设备的信息技术设备电磁兼容抗扰性要求 |
Electromagnetic compatibility immunity requirements for information technical equipment excluding telecommunication terminal equipment |
prEN 556-2-2003 |
医疗器械的消毒 标明为“消过毒”的医疗器械的要求 第2部分:消毒处理的医疗器械的要求 |
Sterilization of medical devices - Requirements for medical devices to be designated STERILE - Part 2: Requirements for aseptically processed medical devices |
prEN 558-3-1991 |
法兰管系统使用的金属阀门 面面间和中心与面间的尺寸 第3部分:级别标记的阀门 |
Metal valves for use in flanged pipe systems; face-to-face and centre-to-face dimensions; part 3: class-designation valves |
prEN 571-3-1995 |
无损检测 渗透检测 第3部分:参照检测样块 |
Non-destructive testing - Penetrant testing - Part 3: Reference test blocks |
prEN 572-8-2001 |
建物筑用玻璃 基本钠钙硅酸盐玻璃制品 第8部分:供料和最终切割尺寸 |
Glass in building - Basic soda lime silicate glass products - Part 8: Supplied and final cut sizes |
prEN 572-9-2001 |
建筑物用玻璃 基本钠钙硅酸盐玻璃制品 第9部分:一致性评价 |
Glass in building - Basic soda lime silicate glass - Part 9: Evaluation of conformity |
prEN 573-4-2003 |
铝和铝合金 锻制产品化学成分和外形 第4部分:产品外形 |
Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 4: Forms of products / Note: Intended as replacement for EN 573-4 (1994-08). |
prEN 573-5-1999 |
铝和铝合金 锻制产品化学成分和外形 第5部分:标准化锻制产品的编纂法典 |
Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5: Codification of standardized wrought products |
prEN 576-2002 |
铝和铝合金 再熔非合金铝锭 规范 |
Aluminium and aluminium alloys - Unalloyed aluminium ingots for remelting - Specifications |
prEN 58-2003 |
沥青和沥青粘合剂 沥青粘合剂取样 |
Bitumen and bituminous binders - Sampling bituminous binders / Note: Intended as replacement for EN 58 (1984-03). |
prEN 593-2003 |
工业阀门 金属蝶阀 |
Industrial valves - Metallic butterfly valves / Note: Intended as replacement for EN 593 (1998-01). |
prEN 60034-20-1-2000 |
旋转电机第20-1部分:控制电机步进电机 |
IEC 60034-20-1: Rotating electrical machinery - Part 20-1: Control motors; Stepping motors |
prEN 60045-1-1992 |
汽轮机第1部分:规范 |
Steam turbines; part 1: specifications (IEC 60045-1:1991) |
prEN 60050-486-1994 |
国际电工词表(IEV)第486章:蓄电池和蓄电池组(IEC 50(486):1999) |
International Electrotechnical Vocabulary (IEV) - Chapter 486: Secondary cells and batteries (IEC 50(486):1991) |
prEN 60056-2000 |
高压交流断路器 |
IEC 60056: High-voltage alternating-current circuit-breakers |
prEN 60056/prA2-2001 |
高压交流断路器 修改prA2:对TRV要求的推荐修改 |
Draft - Amendment 2 to IEC 60056: Recommended changes to TRV requirements |
prEN 60068-3-8-2003 |
环境试验第3-8部分:支持文件和指南从不同振动试验中选择 |
IEC 60068-3-8, Ed. 1: Environmental testing - Part 3-8: Supporting documentation and guidance; Selecting amongst vibration tests |
prEN 60076-11-2002 |
电力变压器第11部分:干式变压器 |
IEC 60076-11: Power transformers - Part 11: Dry-type transformers |
prEN 60076-8-1997 |
电力变压器第8部分:应用指南 |
IEC 60076-8: Power transformers - Application guide |
prEN 60079-1-2003 |
爆炸性环境用防爆电气设备第1 部分:防爆外壳“d” |
IEC 60079-1, Ed. 5: Electrical apparatus for explosive gas atmospheres - Part 1: Flameproof enclosures d |
prEN 60079-19-1992 |
爆炸性环境用防爆电气设备第19 部分:爆炸性环境(矿井或爆破场所除外)修理和大修 |
Electrical apparatus for explosive gas atmospheres; part 19: repair and overhaul for apparatus used in explosive atmospheres (other than mines or explosives) |
prEN 60079-20-1993 |
爆炸性环境用防爆电气设备第20部分:防爆外壳的非金属零件 |
Electrical apparatus for explosive gas atmospheres; part 20: non-metallic parts of flameproof enclosures |
prEN 60079-21-1993 |
爆炸性环境用防爆电气设备第21部分:通气和排气装置 |
Electrical apparatus for explosive gas atmospheres; part 21: breathing devices and draining devices |
prEN 60079-25-2003 |
爆炸性环境用防爆电气设备第25部分:内在安全系统 |
IEC 60079-25, Ed. 1: Electrical apparatus for explosive gas atmospheres - Part 25: Intrinsically safe systems |
prEN 60099-4-2002 |
避雷器第4部分:交流电系统用无间隙金属氧化物避雷器 |
Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. Systems |
prEN 60099-6-2002 |
避雷器第6部分:空隙为串联和并联结构的避雷器额定值等于和小于52kV |
IEC 60099-6, Ed. 1: Surge arresters - Part 6: Surge arresters containing both series and parallel gapped structures; Rated 52 kV and less |
prEN 601-2003 |
铝和铝合金 铸件 与食品接触用铸件的化学成分 |
Aluminium and aluminium alloys - Castings - Chemical composition of castings for use in contact with foodstuff / Note: Intended as replacement for EN 601 (1994-11). |
prEN 60115-9-1-2003 |
电子设备用固定电阻器第9-1部分:空白详细规范具有单个可测量的固定表面装配电阻器网评定级EZ |
IEC 60115-9-1: Fixed resistors for use in electronic equipment - Part 9-1: Blanc detail specification: Fixed surface mount resistor networks with individually measurable resistors; Assessment level EZ |
prEN 60115-9-2003 |
电子设备用固定电阻器第9部分:分规范具有单个可测量的固定表面装配电阻器 |
IEC 60115-9: Fixed resistors for use in electronic equipment - Part 9: Sectional specification: Fixed surface mount resistor networks with individually measurable resistors |
prEN 60118-13-2001 |
助听器第13部分:电磁兼容性(EMC)产品标准 |
IEC 60118-13: Hearing aids - Part 13: Electromagnetic compatibility (EMC); Product standard |
prEN 60118-8-2001 |
助听器第8部分:在模拟现场工作条件下助听器的性能测量方法 |
IEC/CDV 60118-8: Hearing aids - Part 8: Methods of measurement of performance characteristics of hearing aids under simulated in situ working conditions |
prEN 60129-2000 |
IEC 60129的草案修订:交流隔离器和接地开关 |
Draft revision of IEC 60129: Alternating current disconnectors and earthing switches |
prEN 60169-29-1995 |
射频连接器第29部分:具有螺纹推拉、卡锁连接或滑轨或面板用小型射频同轴连接器特性阻抗50欧姆(型号1. |
Draft IEC 60169-29: Radio-frequency connectors - Part 29: Miniature r.f.coaxial connectors with screw-, push-pull, and snap-on coupling or slide-in rack and panel applications - Characteristic impedance 50 ohms (type 1,0/2,3) |
prEN 60182-4-1994 |
绕组线的基本尺寸第4部分:线绕电阻器丝的直径 |
Basic dimensions of winding wires; part 4: diameters of conductors for round resistance wires (IEC 60182-4:1971) |
prEN 60191-2-2001 |
P-VSON略图系列的建议-4/5和6根引线的半导体 |
Proposal for outline family of P-VSON (will be published as Outline 164E-a) - 4/5 and 6 leaded SMD (Body Size D x E: 2,00 x 1,25 mm) (will be published as Outline 161-E-a) |
prEN 60191-6-10-2003 |
半导体器件的机械标准化第6-10部分:P-VSON尺寸的一般规则 |
IEC 60191-6-10, Ed. 1: Mechanical standardization of semiconductor devices - Part 6-10: General rules for the preparation of outline drawings of surface mounted semiconductor device packages; General rules for the dimensions of P-VSON |
prEN 60191-6-11-2002 |
半导体器件的机械标准化第6-11部分:矩形小间距球状排列(FBGA)的包装设计指南 |
Mechanical standardization of semiconductor devices - Part 6-11: General design guidelines for rectangular Fine Pitch Ball Grid Array Packages (FBGA) |
prEN 60191-6-2003 |
半导体器件的机械标准化第6部分:表面安装半导体器件封装外形图绘制的一般规则 |
Mechanical standardization of semiconductor devices - Part 6: General rules for the preparation of outline drawings of surface-mounted semiconductor device packages |
prEN 60191-6-7-2003 |
半导体器件的机械标准化第6-7部分:P-VQFN尺寸的一般规则 |
IEC 60191-6-7, Ed. 1.0: Mechanical standardization of semiconductor devices - Part 6-7: General rules for the dimensions of P-QFN |
prEN 602-2003 |
铝和铝合金 锻制品 生产与食品接触的材料中使用的半成品的化学成分 |
Aluminium and aluminium alloys - Wrought products - Chemical composition of semi-finished products used for the fabrication of articles for use in contact with foodstuff / Note: Intended as replacement for EN 602 (1994-11). |
prEN 60204-X-1994 |
机械的安全机械的电气设备第X部分:电压36kV的高压设备的一般要求 |
Safety of machinery; electrical equipment of machines; part X: general requirements for high voltage equipment for voltages up to 36 kV |
prEN 60225-1992 |
电声学、八频带和小八带过滤器 |
Electroacoustics; octave-band and fractional octave-band filters |
prEN 60225-22-7-2001 |
电气继电器第22-7部分:量度继电器和保护装置的电气骚扰试验 |
Electrical relays - Part 22-7: Electrical disturbance tests for measuring relays and protection equipment; Power frequency imunity test |
prEN 60247-2001 |
标准号: |
中文标题: |
prEN 60264-4-1-1997 |
绕组线的包装第4-1部分:试验方法热塑性材料交货线盘 |
|
prEN 60269-3-1-1992 |
低压熔断器第3-1部分:非熟练人员使用的熔断器(主要是家用和类似用途的熔断器)的补充要求第3节:针形 |
Low-voltage fuses; part 3: supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications); section III: pin-type fuses |
prEN 60282-2-1995 |
高压容断器第2部分:喷射式熔断器 |
Draft IEC 282-2: High-voltage fuses - Part 2: Expulsion fuses |
prEN 60286-6-2003 |
自动装配用件的包装第6部分:表面安装组件的散装盒包装 |
IEC 60286-6: Packaging of components for automatic handling - Part 6: Bulk case packaging for surface mounting components |
prEN 6029-1998 |
航空航天系列耐腐钢具有1.5*螺纹直径最小啮合的UNJ螺纹体可调单叉的棒状端头尺寸和载荷英制系列 |
Aerospace series - Rod-ends, adjustable, single fork with UNJ threaded shank min. engagement: 1,5 * thread diameter in corrosion resisting steel - Dimensions and loads - Inch series |
prEN 60296-2003 |
变压器和开关设备用未使用过的矿物绝缘油规范 |
IEC 60296, Ed. 3: Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
prEN 60298-2002 |
额定电压1KV以上至52KV及以下交流金属封闭开关设备和控制设备 |
AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV |
prEN 60300-3-1-1995 |
可信性管理第3-1部分:应用指南可信性技术分析方法指南 |
Dependability management - Part 3: Application guide - Section 1: Analysis techniques for dependability: Guide on methodology (IEC 60300-3-1:1991) |
prEN 60300-3-12-2001 |
可信性管理第3-12部分:应用指南集成逻辑支持 |
IEC 60300-3-12, Ed. 1: Dependability management - Part 3-12: Application guide; Integrated logistic support |
prEN 60300-3-4-1996 |
可信性管理第3-4部分:应用指南可信性要求规定指南 |
IEC 300-3-4: Dependability management - Part 3: Application guide - Section 4: Guide to the specification of dependability requirements |
prEN 60300-3-9-1995 |
可信性管理第3-9部分:应用指南技术系统的风险分析 |
Draft IEC 300: Dependability management - Part 3: Application guide - Section 9: Risk analysis of technological systems |
prEN 60308-2001 |
水轮机试验控制系统 |
IEC 60308: Hydraulic turbines-testing of control systems |
prEN 60310-2003 |
铁路应用运输车辆的牵引变压器和电感器 |
Railway applications - Traction transformers and inductors on board rolling stock |
prEN 60315-6-1993 |
各种发射类别的无线电接收机的测量方法第6部分:一般用途通信接收机 |
Methods of measurement on radio receivers for various classes of emission; part 6: general purpose communication receivers (IEC 60315-6:1991) |
prEN 60317-41-1996 |
特种绕组线规范第41部分:130L级可软焊聚酯漆包圆铜线 |
IEC 317-41: Specifications for particular types of winding wires - Part 41: Solderable polyester enamelled round copper wire, class 130L |
prEN 60317-54-2001 |
特种绕组线规范第54部分:155L级聚酯漆包圆铜线 |
Specifications for particular types of winding wires - Part 54: Polyester enamelles round copper wire, class 155L |
prEN 60335-2-102-2003 |
家用和类似用途电器设备的安全 第2-102部分:与电器连接的用于燃气、油和固体燃料燃烧设备的特殊要求 |
IEC 60335-2-102, Ed 1.0: Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
prEN 60335-2-104-2002 |
家用和类似用途电器设备的安全 第2-104部分: |
IEC 60335-2-104, Ed. 1.0: Household and similar electrical appliances - Safety - Part 2-104: Particular requirements from air conditioning and refrigeration equipment |
prEN 60335-2-72-2002 |
家用和类似用途电器的安全第2-72部分:工业和商业用地板自动处理机的特殊要求 |
IEC 60335-2-72: Household and similar electrical appliances - Safety - Part 2-72: Particular requirements for automatic machines for floor treatment for industrial and commercial use |
prEN 60335-2-76-2002 |
家用和类似用途电器的安全第2-76部分:栅栏充电器的特殊要求 |
IEC 60335-2-76, Ed. 2.0: Household and similar electrical appliances - Safety - Part 2-76: Particular requirements for electric fence energizers |
prEN 60335-2-79-2002 |
家用和类似用途电器的安全第2-79部分:工业和商业用高压清洁器和蒸汽清洁器的特殊要求 |
IEC 60335-2-79, Ed. 2.0: Household and similar electrical appliances - Safety - Part 2-79: Particular requirements for high pressure cleaners and steam cleaners, for industrial and commercial use |
prEN 60364-5-51/prAA-1994 |
建筑物的电气设施 第5-51部分:电气设备的选择和安装 共同规则的修改草案AA |
Draft amendment to IEC 60364-5-51 (1979): electrical installations of buildings; part 5: selection and erection of electrical equipment; chapter 51: common rules |
prEN 60379-2003 |
家用电热水器性能测试方法草案 |
Methods for measuring the performance of electric storage water-heaters for household purpose (IEC 60379:1987, modifiziert) / Note: Intended as replacement for HD 500 S1 (1988). |
prEN 60384-21-2002 |
电子设备的固定电容器 第21部分:分规范 固体表面1类陶瓷电介质装置的多层固定电容器 评定水平EZ |
Fixed capacitors for use in electronic equipment - Part 21: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, class 1, assessment level EZ |
prEN 60384-22-1-2002 |
电子设备的固定电容器 第22-1部分:空白详细规范 固体表面2级陶瓷电介质装置的多层固定电容器 评定水平E |
Fixed capacitors for use in electronic equipment - Part 22-1: Blank detail specification: Fixed surface mount multilayer capacitors of ceramic dielectric, class 2, assessment level EZ |
prEN 60384-22-2002 |
电子设备的固定电容器 第22部分:分规范 固体表面2级陶瓷电介质装置的多层固定电容器 评定水平EZ 草案 |
Fixed capacitors for use in electronic equipment - Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, class 2, assessment level EZ |
prEN 60384-4-1999 |
电子设备用固定电容器 第4部分:分规范 固体和非固体电解质铝电解电容器 |
Fixed capacitors for use in electronic equipment - Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid electrolyte (IEC 60384-4:1998) |
prEN 60384-4/prA1-1999 |
电子设备用固定电容器 第4部分:分规范 固体和非固体电解质铝电解电容器修改草案1 |
Amendment 1 to IEC 60384-4 |
prEN 60390-2-1997 |
工业用插头、插座和耦合器 第2部分:插销和插套附件的尺寸互换性要求草案 |
Draft IEC 60309-2: Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeablitiy requirements for pin and contact-tube accessories |
prEN 60404-1-1997 |
磁性材料 第1部分:分类 |
Revision of IEC 60404-1: Magnetic materials - Part 1: Classification |
prEN 60416-1994 |
设备用图形符号的一般原则草案 |
General principles for the creation of graphical symbols for use on equipment (IEC 60416:1988) |
prEN 60436-2002 |
家用电动洗碗机 性能测试方法 |
Draft IEC 60436, Ed. 3: Electric dishwashers for household use - Methods for measuring the performance |
prEN 60456-2003 |
家用织物洗衣机 测量性能的方法 草案 |
IEC 60456, Ed. 4.0: Clothes washing machines for household use - Methods for measuring the performance / Note: Intended as replacement for EN 60456 (1999-06). |
prEN 6046-1998 |
航空航天系列耐腐钢球形普通轴承窄系列尺寸和载荷英制系列 |
Aerospace series - Bearings, spherical plain, in corrosion resisting steel - Narrow series - Dimensions and loads - Inch series |
prEN 60466-1992 |
额定电压1KV以上至38KV(包括38KV)交流绝缘封闭开头设备和控制设备 草案 |
A.C. insulation-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 38 kV (IEC 60466:1987) |