标准号 |
中文名称 |
英文名称 |
| BS 4044-1990 |
用梳片式纤维长度分析仪图解法测定纤维长度的方法 |
(Methods for determination of fibre length by comb sorter diagram) |
| BS 4046-1991 |
压缩秸杆建筑平板规范 |
(Specification for compressed straw building slabs) |
| BS 4048 Pts.1 and 2-1966 |
复合钢丝绳和纤维绳规范.复合绳.弹性拉绳 |
(Specification for combined wire and fibre ropes - Combined ropes - Spring lay ropes) |
| BS 405-1987 |
通用未涂覆的板网碳素薄钢板规范 |
(Specification for uncoated expanded metal carbon steel sheets for general purposes) |
| BS 4050-1-1977 |
锦砖拼花地板规范.第1部分:一般特性 |
(Specification for mosaic parquet panels - General characteristics) |
| BS 4050-2-1966 |
马赛克拼花地板规范.分类和质量要求 |
(Specification for mosaic parquet panels - Classification and quality requirements) |
| BS 4051-1987 |
铺地织物厚度的测定方法 |
(Method for determination of thickness of textile floor coverings) |
| BS 4054-1-1995 |
无线电声音广播接收机性能的测定及表示方法.第1部分:一般条件和测量方法(包括音频测量) |
(Methods of measuring and expressing the performance of radio receivers for sound broadcasting - General considerations and methods of measurement, including audio-frequency measurements) |
| BS 4054-3-1996 |
无线电声音广播接收机性能的测量及表示方法.第3部分:调幅声音广播发射用接收机 |
(Methods of measuring and expressing the performance of radio receivers for sound broadcasting. Receivers for amplitude-modulated sound-broadcasting emissions) |
| BS 4054-5-1980 |
无线电声音广播接收机性能的测定及表示方法.第5部分:调频接收机对脉冲干扰响应的测量 |
(Methods of measuring and expressing the performance of radio receivers for sound broadcasting - Measurement on frequency-modulated receivers of the response to impulsive interference) |
| BS 4058-1987 |
数据处理流程图符号.规则和协定规范 |
(Specification for data processing flow chart symbols, rules and conventions) |
| BS 4060-1989 |
压制羊毛毡规范 |
(Specification for pressed wool felts) |
| BS 4062-1-1982 |
液压动力系统用阀门.第1部分:压差/流量特性的测定方法 |
(Valves for hydraulic fluid power systems - Methods for determining pressure differential/flow characteristics) |
| BS 4062-2-1990 |
液压动力系统用阀门.第2部分:性能测定方法 |
(Valves for hydraulic fluid power systems - Methods for determining performance) |
| BS 4064-1966 |
内径测量机械用的平面调整环.米制件 |
(Specification for plain setting rings for use with internal diameter measuring machines - Metric units) |
| BS 4065-1966 |
内径测量机械用的平面调整环.英制件 |
(Specification for plain setting rings for use with internal diameter measuring machines - Inch units) |
| BS 4068-1976 |
仪器、敷料及麻醉师用医院手摇车(包括活角形手摇车)规范 |
(Specification for hospital trolleys for instruments, dressings and for anaesthetists’ use including angular trolleys) |
| BS 4071-1966 |
木材用聚乙酸乙烯酯乳化胶粘剂规范 |
(Specification for polyvinyl acetate (PVA) emulsion adhesives for wood) |
| BS 4072-1999 |
木材防腐备用的铜/铬/砷 |
(Copper/chromium/arsenic preparations for wood preservation) |
| BS 4073-1966 |
矿山矿物运输用重型铁路车辆规范 |
(Specification for heavy rolling stock for mineral haulage in mines) |
| BS 4074-2000 |
沟道钢支柱规范 |
(Specification for steel trench struts) |
| BS 4076-1990 |
钢制烟囱规范 |
(Specification for steel chimneys) |
| BS 4078 Pt.2-1990 |
火药驱动射钉装置.第2部分:工具规范 |
(Powder actuated fixing systems. Specification for tools) |
| BS 4078-1-1987 |
火药驱动射钉装置.第1部分:安全使用实用规程 |
(Powder actuated fixing systems - Code of practice for safe use) |
| BS 4078-2-1990 |
火药驱动安装系统.工具规范 |
(Powder actuated fixing systems - Specification for tools) |
| BS 4082-1-1969 |
立式管线离心泵外部尺寸规范.第1部分:“I“型 |
(Specification for external dimensions for vertical in-line centrifugal pumps - ’I’ Type) |
| BS 4082-2-1969 |
立式管线离心泵外部尺寸规范.第2部分:“U“型 |
(Specification for external dimensions for vertical in-line centrifugal pumps - ’U’ Type) |
| BS 4086-1966 |
受热家用设备的最大表面温度推荐标准 |
(Recommendations for maximum surface temperatures of heated domestic equipment) |
| BS 4087-1989 |
电话和电报用铜包钢导线规范 |
(Specification for copper-covered steel wire for telephone and telegraph purposes) |
| BS 4088-1.1-1994 |
地毯清扫产品.抽样和试验方法.液态产品配方的一般方法 |
(Carpet cleaning products - Methods of sampling and test - General methods for formulations used in liquid form) |
| BS 4088-1.2-1995 |
地毯清洁制品.取样和试验方法.喷雾洗涤机用配方清洁性能测定 |
(Carpet cleaning products - Methods of sampling and test - Determination of cleaning performance of formulations designed for use with spray extraction machines) |
| BS 4088-1.3-1995 |
地毯清洁制品.取样和试验方法.浸入洗涤粉配方总方法 |
(Carpet cleaning products - Methods of sampling and test - General methods for impregnated powder formulations) |
| BS 4088-2-1994 |
地毯清洗剂.液体的泡沫材料配剂规范 |
(Carpet cleaning products - Specification for high foam formulations used in liquid form) |
| BS 4088-3-1995 |
地板清洗产品.喷雾清洗机用液态配方规范 |
(Carpet cleaning products - Specification for spray extraction machine formulations used in liquid form) |
| BS 4088-4-1995 |
地毯清洁制品.浸入洗涤粉配方规范 |
(Carpet cleaning products - Specification for impregnated powder formulations) |
| BS 4089-1999 |
液化石油气和液化天然气用金属软管组件规范 |
(Specification for metallic hose assemblies for liquid petroleum gases and liquefied natural gases) |
| BS 4092-1-1996 |
家用正前门规范.金属门规范 |
(Specification for domestic front entrance gates - Specification for metal gates) |
| BS 4094-1-1966 |
电离辐射防护屏蔽数据推荐标准.第1部分:γ辐射的防护屏蔽 |
(Recommendation for data on shielding from ionizing radiation - Shielding from gamma radiation) |
| BS 4094-2-1971 |
电离辐射防护屏蔽数据推荐标准.第2部分:X 辐射的防护屏蔽 |
(Recommendation for data on shielding from ionizing radiation - Shielding from X-radiation) |
| BS 4098-1975 |
铺地织物厚度、压缩及恢复特性的测定方法 |
(Method for the determination of thickness, compression and recovery characteristics of textile floor coverings) |
| BS 41-1973 |
铸铁套接烟道或烟管及其配件规范 |
(Specification for cast iron spigot and socket flue or smoke pipes and fittings) |
| BS 410-1-2000 |
试验用筛.技术要求和试验.金属丝网布试验用筛 |
(Test sieves - Technical requirements and testing - Test sieves of metal wire cloth) |
| BS 410-2-2000 |
试验筛.技术要求和试验.多孔金属板的试验筛 |
(Test sieves - Technical requirements and testing - Test sieves of perforated metal plate) |
| BS 4102-1998 |
一般栅栏用钢丝线规范 |
(Specification for steel wire for general fencing purposes) |
| BS 4105-1991 |
工业用液态二氧化碳规范 |
(Specification for liquid carbon dioxide, industrial) |
| BS 411-1969 |
木工用圆锯及其附件规范 |
(Specification for circular saws for woodworking and their attachment) |
| BS 4110-1999 |
车辆架驶员护目镜规范 |
(Specification for visors for vehicle users) |
| BS 4115-1993 |
背包式压缩喷雾器规范 |
(Specification for compression knapsack sprayers) |
| BS 4116-4-1992 |
输送机链及其附件与配件链轮.第4部分:输送机链和附件(英制系列)规范 |
(Conveyor chains, their attachments and associated chain wheels - Specification for chains and attachments (British series)) |
| BS 4119-1967 |
固定电阻器产生的电流噪声的测量方法 |
(Method of measurement of current noise generated in fixed resistors) |
| BS 4120-1968 |
幻灯放映机性能的测量方法 |
(Methods for the measurement of performance of still projectors) |
| BS 4129-1990 |
焊接底剂及焊透密封剂的电阻焊性能规范 |
(Specification for welding primers and weld-through sealants, adhesives and waxes for resistance welding of sheet steel) |
| BS 4130-1984 |
氢氧化钠(工业级)规范 |
(Specification for sodium hydroxide (technical grades)) |
| BS 4131-1973 |
水磨石砖规范 |
(Specification for terrazzo tiles) |
| BS 4134-1990 |
工业用缝纫线标签号的标示方法 |
(Method for designation of ticket numbers of industrial sewing threads) |
| BS 4140-0-1986 |
氧化铝的试验方法.一般介绍 |
(Methods of test for aluminium oxide - General introduction) |
| BS 4140-1-1986 |
氧化铝的试验方法.第1部分:试样的制备和贮存 |
(Methods of test for aluminium oxide - Preparation and storage of test samples) |
| BS 4140-10-1986 |
氧化铝的试验方法.未夯实密度的测定 |
(Methods of test for aluminium oxide - Determination of untamped density) |
| BS 4140-11-1986 |
氧化铝的试验方法.第11部分:钠含量的测定 |
(Methods of test for aluminium oxide - Determination of sodium content) |
| BS 4140-12-1986 |
氧化铝的试验方法.第12部分:钒含量的测定 |
(Methods of test for aluminium oxide - Determination of vanadium content) |
| BS 4140-13-1986 |
氧化铝的试验方法.第13部分:试样溶液的盐酸加压处理制备方法 |
(Methods of test for aluminium oxide - Preparation of sample solution by treatment with hydrochloric acid under pressure) |
| BS 4140-14-1997 |
氧化铝的试验方法.钙含量的测定 |
(Methods of test for aluminium oxide - Determination of calcium content) |
| BS 4140-16-1986 |
氧化铝的试验方法.第16部分:用火焰原子吸收法测定锌含量 |
(Methods of test for aluminium oxide - Determination of zinc content by flame atomic absorption) |
| BS 4140-17-1986 |
氧化铝的试验方法.第17部分:氟含量的测定 |
(Methods of test for aluminium oxide - Determination of fluorine content) |
| BS 4140-18-1986 |
氧化铝的试验方法.第18部分:磷含量的测定 |
(Methods of test for aluminium oxide - Determination of phosphorus content) |
| BS 4140-19-1986 |
氧化铝的试验方法.测定硼含量 |
(Methods of test for aluminium oxide - Determination of boron content) |
| BS 4140-1986 |
氧化铝的试验方法.第19部分:硼含量的测定 |
(Methods of test for aluminium oxide. Determination of boron content) |
| BS 4140-2-1986 |
氧化铝的试验方法.在 300℃时质量损失的测定 |
(Methods of test for aluminium oxide - Determination of loss of mass at 300 鳦) |
| BS 4140-20-1980 |
氧化铝的试验方法.第20部分:取样 |
(Methods of test for aluminium oxide - Sampling) |
| BS 4140-21-1980 |
氧化铝的试验方法.第21部分:粒度分析 |
(Methods of test for aluminium oxide - Particle size analysis) |
| BS 4140-22-1980 |
氧化铝的试验方法.第22部分:锰含量的测定 |
(Methods of test for aluminium oxide - Determination of manganese content) |
| BS 4140-23-1987 |
氧化铝的试验方法.第23部分:用氮吸收法(单点法)测定比表面积 |
(Methods of test for aluminium oxide - Determination of specific surface area by nitrogen adsorption (single-point method)) |
| BS 4140-24-1987 |
氧化铝的试验方法.第24部分:粒度分布的测定(用电铸筛分法) |
(Methods of test for aluminium oxide - Determination of fine particle size distribution (method using electroformed sieves)) |
| BS 4140-3-1986 |
氧化铝的试验方法.在1000℃和1200℃时质量损失的测定 |
(Methods of test for aluminium oxide - Determination of loss of mass at 1000 鳦 and 1200 鳦) |
| BS 4140-4-1986 |
氧化铝的试验方法.第4部分:试样溶液的加碱熔化制备 |
(Methods of test for aluminium oxide - Preparation of sample solution by alkaline fusion) |
| BS 4140-5-1986 |
氧化铝的试验方法.第5部分:二氧化硅含量的测定 |
(Methods of test for aluminium oxide - Determination of silica content) |
| BS 4140-6-1980 |
氧化铝的试验方法.第6部分:钛含量的测定 |
(Methods of test for aluminium oxide - Determination of titanium content) |
| BS 4140-7-1986 |
氧化铝的试验方法.第7部分:铁含量的测定 |
(Methods of test for aluminium oxide - Determination of iron content) |
| BS 4140-8-1986 |
氧化铝的试验方法.用比重瓶计测定绝对密度 |
(Methods of test for aluminium oxide - Determination of absolute density using a pyknometer) |
| BS 4140-9-1986 |
氧化铝的试验方法.休止角的测量 |
(Methods of test for aluminium oxide - Measurement of the angle of repose) |
| BS 4142-1997 |
影响住宅和工业混合地区的工业噪声的测定方法 |
(Method for rating industrial noise affecting mixed residential and industrial areas) |
| BS 4145-1967 |
电工用玻璃云母板规范 |
(Specification for glass mica boards for electrical purposes) |
| BS 4147-1980 |
钢铁防护用沥青基热覆层材料(包括相应的底漆)规范 |
(Specification for bitumen-based hot-applied coating materials for protecting iron and steel, including suitable primers where required) |
| BS 4148-1985 |
出版物题名及标题字缩写规范 |
(Specification for abbreviation of title words and titles of publications) |
| BS 4151-1967 |
输入信号为 3至151b/in(压力计)的气动阀定位器的评定方法 |
(Method of evaluating pneumatic valve positioners with input signal of 3 to 15 lbf/in) |
| BS 4154-1-1985 |
热固性聚酯树脂半透明塑料波纹板(玻璃纤维增强的).第1部分:材料和性能要求规范 |
(Corrugated plastics translucent sheets made from thermo-setting polyester resin (glass fibre reinforced) - Specification for material and performance requirements) |
| BS 4154-2-1985 |
热固性聚酯树脂半透明塑料波纹板(玻璃纤维增强的).第2部分:外形和尺寸规范 |
(Corrugated plastics translucent sheets made from thermo-setting polyester resin (glass fibre reinforced) - Specification for profiles and dimensions) |
| BS 416-1-1990 |
砂型铸造或离心铸造的排水和通风铸铁管及配件.第1部分:窝接式系统规范 |
Discharge and ventilating pipes and fittings, sand-cast or spun in cast iron - Specification for spigot and socket systems |
| BS 4162-1983 |
钮扣的试验方法 |
(Methods of test for buttons) |
| BS 4163-2000 |
在学校和类似建筑中设计和技术的安全和卫生.实施编码 |
(Health and safety for design and technology in schools and similar establishments - Code of practice) |
| BS 4164-2002 |
钢铁防护用热覆煤焦油基层材料(包括相应的底漆)规范 |
(Specification for coal-tar-based hot-applied coating materials for protecting iron and steel, including a suitable primer) |
| BS 4167-10-1970 |
电热炊具餐具规范.第10部分:消毒洗池 |
(Specification for electrically-heated catering equipment - Sterilizing sinks) |
| BS 4167-5-1969 |
电热炊具餐具规范.第5部分:蒸汽炉 |
(Specification for electrically-heated catering equipment - Steaming ovens) |
| BS 4168-7-1982 |
内六角螺钉和板手.米制系列.第7部分:内六角圆柱头轴肩螺钉规范 |
(Hexagon socket screws and wrench keys: metric series - Specification for hexagon socket shoulder screws) |
| BS 417-1-1964 |
镀锌低碳钢水槽和盖、箱和筒.第1部分:英制件 |
(Specification for galvanized low carbon steel cisterns, cistern lids, tanks and cylinders. Imperial units) |
| BS 417-2-1987 |
镀锌低碳钢水槽和盖、箱和筒.第2部分:米制件 |
(Specification for galvanized low carbon steel cisterns, cistern lids, tanks and cylinders - Metric units) |
| BS 4172-1-1999 |
手持式消灭家庭飞虫气压瓶.杀虫性能规范 |
(Hand-held pressurized aerosol dispensers against houseflies - Specification for insecticidal performance) |
| BS 4172-2-1999 |
手持式消灭家庭飞虫气压瓶.杀虫性能测定方法 |
(Hand-held pressurized aerosol dispensers against houseflies - Method for determination of insecticidal performance) |
| BS 4174-1972 |
自攻螺钉及金属传动螺钉规范 |
(Specification for self-tapping screws and metallic drive screws) |
| BS 4177-1992 |
炊具控制部件规范 |
(Specification for cooker control units) |
| BS 4181-1-1985 |
橡胶的红外光谱识别.第1部分:烃类橡胶、氯丁橡胶、丁腈橡胶和氯磺化聚乙烯橡胶的识别方法 |
(Identification of rubbers by infra-red spectrometry - Method for identification of hydrocarbon, chloroprene, nitrile and chlorosulphonated polyethylene rubbers) |
| BS 4183-1967 |
机用螺钉和螺母规范.米制系列 |
(Specification for machine screws and machine screw nuts - Metric series) |
| BS 4184-1994 |
开式机械型机动压力机词汇 |
(Glossary for power presses, open front mechanical type) |
| BS 4185-1-1967 |
机床零件.第1部分:防松螺母(“c“型,凹头紧定螺钉锁紧的) |
(Machine tool components - Locknuts (’C’ type, socket set screw locking)) |
| BS 4185-10-1977 |
机床零件.第10部分:丝杠及进给螺杆组件用梯形螺纹 |
(Machine tool components - Trapezoidal threads for lead and feed screw assemblies) |
| BS 4185-11-1983 |
机床零件.第11部分:齿轮精度等级推荐规范 |
(Machine tool components - Recommendations for accuracy grades of gears) |
| BS 4185-13-1985 |
机床零件.第13部分:埋头孔尺寸规范 |
(Machine tool components - Specification for dimensions of counterbored holes) |
| BS 4185-14-1987 |
机床零件.60°中心孔导向杆直径的测定方法 |
(Machine tool components - Method for determination of the pilot diameter of 60 ?centre holes) |
| BS 4185-2-1967 |
机床零件.第2部分:安装环 |
(Machine tool components - Collars) |
| BS 4185-7-1973 |
机床零件.第7部分:宽距夹头 |
(Machine tool components - Wide range collets) |
| BS 4185-9-1976 |
机床零件.第9部分:整平螺钉、螺母及基座板 |
(Specification - Machine tool components - Levelling screws, nuts and seating plates) |
| BS 4189-1967 |
易读性试验用常用活版印刷字符(ISO试验字符)规范 |
(Specification for conventional typographical character for legibility tests (ISO test character)) |
| BS 419-1966 |
电气用浸漆织物和织带规范 |
(Specification for varnished fabrics and tapes for electrical purposes) |
| BS 4190-2001 |
ISO 米制的粗制六角螺拴螺钉和螺母规范 |
(ISO metric black hexagon bolts, screws and nuts - Specification) |
| BS 4193-1-1993 |
镶硬质合金刀具.第1部分:切削刀具用可转位刀片的命名规范 |
(Hardmetal insert tooling - Specification for designation of indexable inserts for cutting tools) |
| BS 4193-10-1982 |
镶硬质合金刀具.第10部分:带可转位刀片和莫氏锥柄的端铣刀规范 |
(Hardmetal insert tooling - Specification for end mills with indexable inserts and Morse taper shank) |
| BS 4193-11-1983 |
镶硬质合金刀具.第11部分:带可转位刀片的平面铣刀尺寸规范 |
(Hardmetal insert tooling - Specification for dimensions of face milling cutters with indexable inserts) |
| BS 4193-12-1984 |
镶硬质合金刀具.第12部分:带可转位刀片的侧面铣刀及端面铣刀和切槽刀的尺寸规范 |
(Hardmetal insert tooling - Specification for dimensions of side and face milling and slotting cutters with indexable inserts) |
| BS 4193-13-1998 |
硬质合金镶齿工具.带园角的可转位硬质金属镶齿.部分圆柱型固定孔.尺寸 |
(Hardmetal insert tooling - Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole - Dimensions) |
| BS 4193-14-1997 |
镶硬质合金刀具.第14部分:可转位刀片用镗杆(圆柱柄刀夹)命名规范 |
(Hardmetal insert tooling - Specification for designation of boring bars (tool holders with cylindrical shank) for indexable inserts) |
5分钟获取标准报价 咨询电话：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com